Precision-digital PD6100 Manual de usuario descargar pdf (Pagina 17)

100

Model PD6100 Strain Gauge/Load Cell Meter Instruction Manual

Configuration for 12 or 24 VDC Input Power Option

Warning!

Do not exceed voltage rating of the selected

configuration.

Meters equipped with the 12/24 VDC power option are shipped

from the factory ready to operate from 24 VDC.

To configure the meter for 12 VDC power:

1. Remove all the connectors.

2. Unscrew the back cover.

3. Slide the back cover about 1 inch.

4. Configure the J9 jumper, located behind the power

connector, for 12 V as shown below.

Figure 5. Jumper Configuration for 12/24 VDC Input Power

MAIN BOARD

24 VDC

12 VDC

POWER

12 V

24 V

J9 CONFIGURATION

Factory

Default

M-LINK

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 99 100

PD6100 Instruction Manual 1
Disclaimer 2
Limited Warranty 2
Registered Trademarks 2
Table of Contents 3
Table of Figures 6
INTRODUCTION 6
ORDERING INFORMATION 7
SPECIFICATIONS 8
Strain Gauge Input 10
COMPLIANCE INFORMATION 12
SAFETY INFORMATION 14
INSTALLATION 14
Square Corners to 0.060" 15
(1.5mm) Max 15
Mounting Dimensions 16
MAIN BOARD 17
Connections 18
Connectors Labeling 19
Warning! 19
Power Connections 19
Switch Configuration 20
INPUT SIGNAL 22
3-Wire 100 mV 23
Transducer 23
RELAY4 RELAY3 24
RELAY2 RELAY1 24
Switching Inductive Loads 25
4-20 mA Output Connections 26
Analog Output Power Supply 26
F4 Digital Input Connections 26
RLY5 RLY6 RLY7 RLY8 27
NO C NO C NO C NO C 27
Interlock Relay Feature 28
SETUP AND PROGRAMMING 29
Setting Numeric Values 34
Main Menu 35
Setting Up the Meter (setup) 36
Programming the Meter (prog) 42
Dual-Scale Application 45
Error Message (Error) 46
Setup menu 46
Minimum Input Span 46
Display Setup Menu 48
Setting the Relay Action 50
Setting Fail-Safe Operation 51
Programming Time Delay 51
Manual (latching) 53
Automatic (non-latching) 53
Time Delay Operation 58
Relay Operation Details 59
Front Panel LEDs 60
Non-Latching Relay (Auto) 61
Non-Latching Relay (A-man) 61
Latching Relay (LatcH) 61
Latching Relay (Lt-Clr) 62
Acknowledging Relays 62
Pump Alternation Operation 63
DI 1-4 DO 1-4 66
5 VDC GND 66
Setting Numeric 67
Reset Menu (reset) 70
Tare Menu (Tare) 70
Control Menu (Contrl) 71
Advanced Features Menu 71
Noise Filter (filter) 75
Noise Filter Bypass (bypass) 75
Rounding Feature (round) 75
Select Menu (SElect) 77
Auto-Zero (Auto 0) 78
Low-Flow Cutoff (CutofF) 79
Error Message (error) 83
Meter Copy Function (Copy) 84
METER OPERATION 85
Maximum/Minimum Readings 86
TROUBLESHOOTING 87
Symptom Check/Action 92
LIM6100_B 100
SFT039 Ver 3.200 & up 100

Comentarios a estos manuales

Sin comentarios

Precision-digital PD6100 Manual de usuario Pagina 17

Comentarios a estos manuales

Relacionado con productos y manuales para Panel De Control Precision-digital PD6100